How To Take The Governor Off A Golf Cart? Follow These Simple Steps!

Spread the love

If you are an avid golf cart enthusiast, then you know how important it is to keep your golf cart running smoothly. One of the most common issues people face with their golf cart is being limited by its maximum speed – this is where the governor comes in.

Golf carts come with governors that regulate their top speed as a safety precaution for both passengers and drivers alike. While limiting speed can be beneficial, there might be instances when taking off the governor becomes necessary – like when using the cart as a utility vehicle on private property or attending a specialized racing event.

Understandably, removing the governor seems complicated; some even regard it as impossible without professional help. However, this article provides you with simple steps on how to take the governor off a golf cart safely and efficiently, allowing you to enjoy increased speed whenever needed.

“There’s no better feeling than cruising around the green at lightning speeds during special events or while performing tasks on your property, knowing you’re not restricted by pre-determined limitations.”

In the following sections, we’ll provide you with detailed instructions aimed at helping you undertake this process yourself. So, buckle up, and let’s get started!

Understand What A Governor Is And How It Works

Definition of a Governor

A governor is an engine-speed regulator designed to limit the top speed of a golf cart. The device controls the amount of fuel flow going into the carburetor or injector, thereby regulating engine RPM and ultimately limiting the maximum speed.

How a Governor Works

The most common type of governor used in golf carts is the mechanical governor. It works by using weights and springs that respond to changes in engine speed. When the system detects that the RPM has reached a certain level, it interrupts the fuel supply to the carburetor, causing the engine to slow down. This cycle continues until the desired speed is achieved, at which point the governor stabilizes fuel intake to maintain that particular speed.

Modern govenors also come with electronic sensors to help regulate engine performance. These sensors send data about the engine’s ignition timing, airflow, and more to an onboard computer that monitors these metrics and adjusts the governor as necessary.

Importance of a Governor in Golf Carts

In many countries where golf carts are popular forms of transportation both on and off the course, there are strict regulations regarding their use. In response, many manufacturers incorporate governors into the design of their carts to ensure compliance with legal requirements such as speed limits, emissions standards, and noise ordinances. Additionally, governors can prevent reckless driving, injuries, and accidents caused by overspeeding.

Problems with Governors

Most of the problems associated with governors are related to malfunctions that lead to either incorrect regulation or the complete shut-off of engine power. Some common issues include wear and tear of governor parts, broken linkage, and improperly adjusted or calibrated governors. Fortunately, most issues with governors in golf carts can be fixed by experienced mechanics.

“A governor is something that controls the settings on a machine, like an engine. It keeps things under control and functioning properly.” -Harvey Mackay

As important as they might seem, removing or disabling governors in your golf cart can be dangerous and illegal in many states and countries. Doing so may cause mechanical malfunctions leading to serious accidents, harm passengers as well as yourself, void manufacturer warranties, or even result in hefty fines and legal action. Thus, it’s essential to observe proper handling of these devices. If one deems necessary to adjust their golf cart’s governance, consulting the mechanic first is crucial.

Determine The Type Of Governor Your Golf Cart Has

If you’re looking to take the governor off your golf cart, the first step is to determine what type of governor it has. This information will help you understand how to remove it safely and effectively.

Electric Governors

Many newer models of golf carts come equipped with electronic governors, which use electronic sensors to regulate the speed of the vehicle. If your golf cart has an electric governor, there are a few things you should know before attempting to remove it:

  • Disconnect the battery before working on any electrical components of the golf cart.
  • Locate the governor module in the cart’s wiring system. It may be located near the motor or under the dash.
  • Unplug the connector that leads to the governor module and remove the module from its mounting location.
  • Consult your owner’s manual or the manufacturer’s website for further instructions specific to your model of golf cart.

Mechanical Governors

Older models of golf carts often feature mechanical governors, which use a combination of springs and linkages to limit the speed of the cart. Removing a mechanical governor can be accomplished in a few easy steps:

  • Locate the governor assembly, which is typically bolted directly onto the engine block.
  • Remove the bolts that hold the governor assembly in place using a socket wrench or pliers.
  • Once the assembly is loose, disconnect any linkage rods or cables that attach it to the carburetor or throttle control.
  • Install a new venturi that will allow air through the carburetor without restricting fuel flow.
“Removing a governor from a golf cart can be dangerous if the proper precautions are not taken. Always consult your owner’s manual or seek professional assistance to ensure that you stay safe and avoid any potential damage to your vehicle.” -Golf Cart Resource

Whether your golf cart has an electronic or mechanical governor, it’s important to take safety seriously when attempting to remove it. By following these tips and consulting with professionals as needed, you can safely and effectively get rid of the governor on your golf cart and enjoy more freedom on the course.

Gather The Tools You Need To Remove The Governor

Screwdrivers and Wrenches

If you want to take the governor off your golf cart, then you will need some specific tools that can help you get the job done. For starters, it is important to have a set of screwdrivers and wrenches on hand. These tools will come in handy when trying to remove any bolts or screws that are holding the governor in place.

A socket wrench and torque wrench can also be useful for this particular task. Make sure you have different sizes of sockets and hex heads available so that you can work with any size bolt or nut that you come across as you take apart the pieces of your golf cart.

Wire Cutters and Strippers

In addition to screwdrivers and wrenches, you should also have wire cutters and strippers handy. This is because there may be wires connected to the governor that need to be removed before you can fully take it off the golf cart.

When using wire strippers, make sure to choose a setting appropriate for the gauge of the wire so that you do not accidentally strip too much insulation.

“Good tools are essential for getting the job done right.” -Michael Johnson

Having these tools on hand will ensure that you have everything you need to safely and effectively take the governor off your golf cart. Make sure to gather them together before starting any work so that you can minimize the risk of damaging any part of your vehicle unintentionally.

Disconnect the Governor’s Control Module

Golf carts are primarily designed for recreational use, and some golf cart enthusiasts love to push their carts beyond their standard speed limits. To increase the top speed of a golf cart, you need to remove its governor control module.

Locating the Control Module

The first step in this process is to locate the control module that governs your cart’s speed. On most golf carts, the controller box can be found beneath the seat or under the cart chassis.

If you’re unsure where exactly to find it on your particular model, check online forums or consult the manufacturer’s manual. You could also contact an authorized dealer for advice and guidance.

Disconnecting the Control Module

To disconnect the governor control module, you will have to follow these steps:

  • Step 1: Turn off the Golf Cart – make sure the key is out of the ignition and the emergency brake is engaged; you don’t want any accidents during this procedure.
  • Step 2: Open the Seat – lift the front edge of the seat bottom and swing upwards to expose the battery compartment and cables.
  • Step 3: Find the Controller Box – the controller should be attached to the frame of the cart or hidden behind all the wires and connection points between batteries.
  • Step 4: Disconnect Wires – using basic hand tools remove the cover off the controller box to reveal multiple wiring harnesses and connectors. Using special pliers, gently pull apart each connector until they’re separated safely from the Controller Box. The number of wires connected depends upon the golf cart make and model so refer to the manufacturer’s guide if necessary.
  • Step 5: Remove the Controller – unscrew the heel of its bracket and take the controller box out.

After you have removed the governor’s control module, your golf cart will operate at higher speeds than before. However, recklessness on the road can be dangerous for both the driver and other pedestrians or drivers.

“Speed has never killed anyone. Suddenly becoming stationary, that’s what gets you.” – Jeremy Clarkson

With that said, it’s critical to note that driving safely and responsibly is crucial while operating a modified golf cart. Most states have specific laws regarding the suitability of using such carts in public roads; therefore, make sure you are legally allowed to use it and don’t forget to inform yourself about traffic rules in each location where you plan to ride.

Removing a governor from a golf cart can improve speed performance. By following our guide above step by step, you should be able to disconnect the governor control module without causing any damage to your vehicle. Safety must always come first, so ensure that you remain cautious and knowledgeable of state regulations as you drive around with a modified golf cart.

Remove The Governor’s Hardware And Cable

Locating the Governor Hardware and Cable

If you are looking to take your golf cart off-road or increase its speed, you might consider removing the governor. The first step in this process is locating the governor hardware and cable.

The governor in a golf cart is usually located on the engine, close to the carburetor. It consists of two parts: the governor gear and the governor cable. The governor gear regulates the amount of fuel that enters the carburetor, while the governor cable limits the maximum speed of the golf cart by controlling the throttle valve.

Removing the Governor Hardware and Cable

Once you have located the governor hardware and cable, it’s time to remove them. Here are a few simple steps:

  • Disconnect the battery to prevent any electrical shocks or accidents caused by accidental starting of the vehicle.
  • Detach the air filter housing from the engine, using a socket wrench if necessary.
  • Locate the governor arm, which should be next to the carburetor. Follow the governor cable from the governor arm to where it attaches to the engine.
  • Use pliers to grip and pull the cotter pin away from the governor arm. Twist and slide the governor arm out of place.
  • Next, locate the governor-gear system. This will typically be near the carburetor as well. Use a socket wrench to remove the bolt holding it in place. Retrieve the washer and other associated pieces for later reassembly if required.
  • Gently disconnect the governor cable from the carburetor. Carefully slip the cable free from the sheath, ensuring that no sharp edges cut into or damage the cable.
  • After removing the governor gear and cable, make sure all hardware and parts are put back in their proper place. Install new carburetor linkages and springs to adjust the throttle but use caution as any adjustments should be small so you do not over-rev your engine impacting performance negatively.
“Going off-road requires that you have a firm understanding of how every component on your vehicle operates.” -Tanner Foust

If you’re unsure about any part of this process, seek help from an experienced mechanic or service technician before proceeding.

With the right tools and a little elbow grease, removing the governor hardware and cable from your golf cart is a simple DIY project. Always remember to fix any hardware correctly and understand that removing the governor will impact your engine’s capabilities drastically. So take it slow, and always prioritize safety when working on automotive projects.

Test Your Golf Cart After Removing The Governor

If you recently removed the governor from your golf cart, you may be wondering how to test it and ensure that everything is working properly. Here are a few steps you can take to check the speed and any warning lights on your cart.

Turn on the Golf Cart

The first step in testing your golf cart after removing the governor is to turn it on and let it warm up. This allows all of the components to get ready for operation and ensures that your test results are accurate. Turn the key or press the pedal (depending on your model) and let the engine run for a minute or two before moving onto the next step.

Test the Speed of the Golf Cart

Once your golf cart is warmed up, you can start testing its speed. Find an open area such as a parking lot or unused road where you can drive safely without interference from other vehicles or pedestrians. Begin by driving straight ahead at full throttle and note the speedometer reading. If your cart does not have a speedometer, use a GPS speedometer app on your phone to measure the speed.

You should notice a significant improvement in speed compared to when the governor was installed. However, you still need to exercise caution when driving since higher speeds increase wear and tear on the vehicle and decrease the handling ability of the driver.

Check for any Warning Lights

Last but not least, you’ll want to inspect the dash area for any new warning lights that may have appeared after removing the governor. These lights could indicate issues with the engine or other critical systems within the golf cart.

Common warning lights that might appear include battery warning, oil pressure light, brake warning, and temperature warning light. If any new warning lights appear after removing the governor from your golf cart, it’s best to have a professional mechanic inspect the vehicle and diagnose any potential issues.

“The problem with golf is… that the ball always waits for you; human life never does.” -Rufus Isaacs

Testing your golf cart after removing the governor requires careful attention to detail and adherence to safety guidelines. Following the steps above can help you check the speed and warning lights on your newly updated cart so that you can enjoy its newfound freedom of movement.

Frequently Asked Questions

What tools do I need to take the governor off a golf cart?

To remove the governor from your golf cart, you’ll need a socket wrench, screwdriver, and pliers. You may also need a pair of vice grips and a torque wrench. Make sure you have the right size sockets and screwdrivers for your particular golf cart model. It’s important to follow your golf cart manufacturer’s instructions when removing the governor.

Is it legal to remove the governor from a golf cart?

It is generally not legal to remove the governor from a golf cart. Golf carts are designed to have governors to prevent them from going too fast. Removing the governor can make the golf cart unsafe and dangerous to operate on public roads or in crowded areas. If you are caught driving a golf cart without a governor, you may face fines or other penalties.

What are the risks of taking the governor off a golf cart?

Taking the governor off a golf cart can be dangerous. The governor is designed to limit the speed of the golf cart, which helps keep the driver and passengers safe. Removing the governor can cause the golf cart to go too fast, which can lead to accidents and injuries. Additionally, removing the governor can cause the golf cart to wear out more quickly, leading to costly repairs and maintenance.

How do I adjust the governor on my golf cart?

To adjust the governor on your golf cart, you’ll need to locate the governor on your particular model. Once you’ve found the governor, you can adjust it using a screwdriver or wrench. Turning the screw clockwise will increase the speed of the golf cart, while turning it counterclockwise will decrease the speed. It’s important to make small adjustments and test the golf cart’s speed before making any additional adjustments.

Can I remove the governor on an electric golf cart?

It is possible to remove the governor on an electric golf cart, but it is not recommended. Electric golf carts are designed to have governors to prevent them from going too fast. Removing the governor can cause the golf cart to go too fast, which can be dangerous. Additionally, removing the governor can cause the golf cart to wear out more quickly, leading to costly repairs and maintenance. It’s best to leave the governor on your electric golf cart in place.

Do NOT follow this link or you will be banned from the site!